FREE SHIPPING when purchase RM 100.00 and above. Terms and Condition Apply
TNG Payment available NOW
HARDEX
HARDEX
Sort by
Show result

Special Features:- 

~Permanent Thread locking
~High Strength.
~High Viscosity.
~Providing Permanent Assembly.
~Can Stand High Temperature From 67 F  to 302 F ( -55°C -  150°C ) .
~Resistant To Heavy Shock And Vibration
~Ideal Applications Are Loose Fitting Bearing Shafts, Flanges, Piston
~Rods, Big Plant Furnace Studs, Locking Bolts And Studs Up To M36.

Direction:

1 . Surfaces Must Be Cleaned And Dry.
2. Shake The Bottle Before Use.
3. Apply Sufficient Thread - Lok To Both Surfaces.
4. Assemble Components And Removes Excess Thread - Lok.
5. Allow Assembly To Cure In A Few Minutes And Full Strength After 24 hours . ( It Depends On Product Grade And Type Of Surface )

Caution: Must Protect Own Skin And Eyes, May Cause Skin And Eye Irritation.

RM14.00

Special Features:- 
For best results:
~Make sure the surfaces to be joined are clean.
~Squeeze equal parts of resin and hardener and mix thoroughly.
~Use within 5minutes (if at 27C room temp)
~Pull plunger back slightly and place the breakaway portion between plunger firmly over nozzles.

 

RM10.00

Special Features:-  

~Applicable for Transmission Oil Pan 
~Gearbox
~Engine/Motor ~
~High Temperature Piping System 

Directions: 
1. Surfaces must be clean, dry and il free.
2.Pierce seal at the end of the metal tubes with reverse end of cap
3.Screw on nozzle and cut to desired bead size.
4.Apply even bead  (1/16''~1/8'') around perimeter of surface.
5. Assemble part once silicone skinned (~15minutes)
6. Remove excess silicone. Do not squeeze silicone by overtighten bolt.
7. Clean nozzle, replace cap after use. 

RM11.00

Special Features:- 
~Applicable for Bath Tub 
~Kitchen 
~Basins
~Bathroom 

Directions: 
1. Surfaces must be clean, dry and oil free 
2. Remove storage cap and pierce the end of the tube. Cut nozzle to desired opening and screw to the tube.
3. Hold tube at slight angle, squeezing tube from bottom with firm and continuous pressure.
4. Wipe offf excess sealant with paper towel. Damp cloth with turpentine or solvent to wipe off wrongly applied area to avoid staining 
5. Set in 10 to 15 minutes and can be handle in 1 hour. Fully bond in 24 hours.

 

RM11.00

Special Features:- 
~Applicable for Transmission Oil Pan 
~Gearbox
~Engine / Motor
~ High- Temperature Piping System 


Directions: 
1. Sufaces must be clean, dry and oil free.
2. Pierce seal at the end of the metal tube with reverse end of cap.
3. Screw on nozzle and cut to desired bead size.
4. Apply even bead (1/16''~1/8'') around perimeter of surface.
5. Assemble part once silicone skinned (~15minutes)
6. Remove excess silicone. Do not squeeze silicone by overtighten bolt.
7. Clean nozzle, replace cap after use. 
8. Silicone fully cured in 24hours
 

RM11.00

Special Features:- 
~Aplicable for Window glazing 
~Shop front 
~Aquarium 
~Bathroom 

Directions: 
1. Make sure surfaes clean, dry, free from dust and oil before apply.
2. Remove cap and pierce the end of the tube, Cut nozzle to desired opening and screw to the tube.
3. Hold tube at slight angle, squeezing tube from bottom with firm and continuous pressure.
4. Wipe off excess sealant with paper towel. Damp cloth with tupentine or solvent to wipe off wrongly applied area to avoid staining.
5. Set in 15 minutes and can be handle in 1 hour. Fully bond in 24 hours. 

RM11.00

Special Features:- 
~Aplicable for Transmissions Oil Pan,
~Gearbox
~Engine/motor
~High Temperature Piping System
Directions: 
1. Sufaces must be clean, dry and oil free.
2. Pierce seal at the end of the metal tube with reverse end of cap.
3. Screw on nozzle and cut to desired bead size.
4. Apply even bead (1/16''~1/8'') around perimeter of surface.
5. Assemble part once silicone skinned (~15minutes)
6. Remove excess silicone. Do not squeeze silicone by overtighten bolt.
7. Clean nozzle, replace cap after use. 

 

RM17.00

Special Features:- 
~All Weather Roofing Compound Is A Heavy Duty, Solvent Based Bituminous Roof Coating, Compounded With Fillers And Fibres.
~It Is Resistant To Wash Off By Rain Almost Immediately After Application And Is Therefore Particularly Suited To Winter Use.
~It Is Specially Formulated For The Treatment Of Cracks In Concrete, Bricks, Roofing, Asbestos Sheets, Etc.
~Suitable For, Asphalt Roofs, Built Up Felt Roofs, Iron, Steel, Zinc & Lead, Asbestos-Cement Sheeting, Slates,Tiles, Concrete Roof Decks, Metal.
~All Weather Roofing Compound May Be Applied By Brush Or Spray To Waterproof And Reseal Many Different Types Of Roof Covering.
~Brushable Consistency Or With Spray Equipment, Good Waterproofing Properties.
~Tough, Fibre Reinforced For Strength.
~Made In Malaysia.

RM12.50