FREE SHIPPING when purchase RM 100.00 and above. Terms and Condition Apply
TNG Payment available NOW
V-TECH
V-TECH
Sort by
Show result

Special Features:- 

~Directions:
1. Surfaces must be clean, dry and free of dirt, grease, oil or water. Puncture with top of cap and install nozzle.
2. Apply one drop to one surface only. Assemble both surfaces together and hold for few seconds to enable it to set completely. 
3. Replace cap after use and store in a cool, dry place. 

RM1.90

Special Features:- 

~Directions:
1. Surfaces must be clean, dry and free of dirt, grease, oil or water. Puncture the tube with the cap and install nozzle.
2. Squeeze tube and push sealant ahead of nozzle to achieve a smooth finish.Sealant skins in 5 minutes, dries to touch in 1 hour and is fully cured in 24 hours.
3. Uncured sealant can be cleaned up with mineral spirits 
4. Replace cap after use and store in cool, dry place.

RM9.00

Special Features:-

~Directions:
1. Surfaces must be clean, dry and free of dirt, grease, oil or water. Puncture tube with cap.
2. Apply product to substrate.
3. If used as adhesive: Press firmly and let it cure for 6 hours before moving it.
4. If used as sealant: Tool within 5minutes of extrusion. 
5. Replace cap after use and store in a cool, dry place. 
6.Product can be cleaned with mineral spirit, 

 

RM8.00

Special Features:- 

~Directions:
1. Surfaces must be clean, dry and free of dirt, grease, oil or water. Puncture tube with cap.
2.Apply product to substrate.
3. If used as adhesive: Press firmly and let it cure for 6 hours before moving it.
4. If used as sealant: Tool within 5 minutes of extrusion.
5.Replace cap after use and store in a cool, dry place. 
6. Product can be cleaned with mineral spirit.

RM9.00

Special Features:- 
~Directions: 
1. Surfaces must be clean, dry and free of dirt, grease,oil or water.
2. Apply adhesive with a brush or spatula onto one side of the substrate.
3. Assemble the substrates immediately or within 5 minutes after the applications.
4. Iron the substrates after approximately 30 minutes to shorten the curing time and improve resistance towards washing and cleaning materials (Iron setting according to the type of substrate).
5. Remove the fresh specks of glue with water immediately. Cured glue will be extremely difficult to remove.
6. Replace cap after use and store in a cool, dry place.

RM8.50

Special Features:- 

~Directions
1. The surface should be free from oil, dirt, rust, and other contaminants.
2. Shake the product throughly before use. 
3. For Through Hole Assembly, apply several drops of the product onto the bolt and the nut at the nut engagement area.
4. For blind hole assembly, apply the product into the bottom of the hole. Installation of the fastener will displace the air and force the adhesive upward into the threads.
5. For Sealing applications, apply a 360 celcius bead to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to throughly fill the voids.
6.For Diassembly, remove with standard hand tools, or apply localized heat to the nut or bolt to approximately 250 and disassembly while hot.

RM14.00

Special Features:- 

~Not suitable for bonding of polythylene, polypropylene, PTFE and other flexible materials. 
~Directions: 
1. Surfaces must be clean, dty and free of dirt, grease oil or water.
2.Puncture tube with the cap and squeeze out equal amounts of resin and hardener on any disposable container or surface. 
3. Mix throughly and apply mixture to both surfaces before joining 
4. Replace cap after use and store in a cool, dry place. 

RM8.00

Special Features:- 

~Directions: 
1. Before applying, roughen and clean the area to be repaired.
2. Cut or twist off required amount
3. Mix by kneading with fingers to a uniform color. If mixing is difficult, warm Rapid Steel epoxy to room temperature or slightly above, or use damp fingers for easier mixing and application. 
4. As the epoxy is mixed, the two contrasting colors blend into one color to indicate complete mixing. 
5. Apply to surface to be repaired (within two minutes of mixing) 
6. Force into any cracks or holes and strike off excess material before hardening begin, preferable with a tool wet with clean water.
7. When applying to a damp, wet or slowly leaking area, work the material forcefully into the surface and apply pressure until adhesion begins to take effect. 

RM11.00

Special Features:- 
~Directions:
1. Surfaces must be clean, dry and free of dirt, grease, oil or water.Puncture tube with cap.
2. Apply adhesive onto both sides of the surface to be bonded and allow solvent to evaporate (5-10 minutes).
3. Once the adhesive is tacky, press both surfaces firmly. Maintain pressure for at least 24 hours.
4. Replace cap after use and store in a cool, dry place. 

 

RM4.00

Special Features:- 

~Directions:
1.Surfaces must be clean, dry and free of dirt, grease, oil or water. Puncture the tube with the cap and install nozzle.
2.Squeeze tube and push adhesive ahead of nozzle. Press firmly over entire surfaces to transfer adhesive and then pull both surfaces apart. 
3. Allow to tack off for 3-5minutes and reposition and press firmly together.
4. Replace cap after use and store in a cool, dry place. 

RM8.50

Special Features:- 

~Surface Preparation 
1. Substrate must be smooth, flat, clean, dry and free of excessive moisture and alkali. Remove dirt, wax, grease, paints,oil, sealers, curing compounds and all foreign matter that would interfere with proper adhesion.
2. The installation site should have a consistent room temperature of 18-35 celcius to allow for proper acclimation. 

~Directions
1. Apply the adhesive uniformly onto one surface 
2. Spread sufficient amounts of adhesive with a trowel in an area that can covered within 10-30 minutes 
3. Place together the surfaces while adhesive is still wet 
4. Joint surfaces must be held together for at least 36 hours. Clamping for furniture parts or weight for flooring, are required. 

RM5.00

Vtech 3second Super Glue 502 For Various Material, Glass, Plastic, Tiny Wood 

Features:-
Durable and Practical
Full Curing Time: 24h
Surface Dry Time: 3~6s
Quick Dying, Easy To Use
Color: Transparent Water-like
Multi Purpose Use Super Glue

RM3.90

Vtech Glass & Metal Silicone Sealant VT-218 White , Clear For Aquarium, Basin Bathroom , Ceramic Tiles, Glass Window ,Aluminium 

Features:
Brand: V-Tect
Colour Variants: White & Clear
Volume: 300ml
Model: VT-218
Neutral Silicone
Low VOC compliant
Excellent adhesion
Flexible seal
Excellent weather resistance

RM14.00

Vtech Silicone Sealant Black, White, Clear For Aquarium, Basin Bathroom , Ceramic Tiles, Glass Window ,Aluminium 

Features:
Brand: V-tech
Colour Variants: Black, White, Clear
Volume: 240ml
Model: VT202
Acetic Silicone
Versatile Sealant
Durable And Flexible
Indoor And Outdoor Use

RM11.00